Pines #3 & #4 Tube & Pipe Benders
Swing Arm Assembly


Note: Click on large image when it appears for fully expanded view.

KEY
H.I.T. PART NO.
REPLACES
PART NO.
NO.
REQ'D

DESCRIPTION
1 (LH)
60020-07200 114-20-072-00
1
Swing Arm Weldment – LH (CCW)
1 (RH)
60025-07200 114-25-072-00
1
Swing Arm Weldment – RH (CW)
2
60010-29500 114-10-295-00
1
Gib, Slide
3
60010-30700 114-10-307-00
2
Slide Guard - Brass
4
60010-43000 114-10-430-00
4
Toggle Link (w/ 2 Bushing 60010-43000-BB)
4-1
60010-43000-BB (if sold separately)
8
Bushing Only, Toggle Link (ID Sizing Req’d)
5
60010-50401 114-10-504-01
1
Pin – Clevis (Includes $7)
6
60010-50402 114-10-504-02
1
Pin – Upper Rear (Includes $12)
7
60010-50600 114-10-506-00
1
Pin – Rod End (Includes $8 & $12)
8
60010-51000 114-10-510-00
1
Pin – Slide (Includes $8 & $12)
9
60010-65200 114-10-652-00
1
Rod End – Clamp Cylinder
10 (LH)
60010-72400 114-10-724-00
1
Slide – Steel / Phenolic, LH (used on LH only!)
10 (RH)
60025-72400 114-25-724-00
1
Slide – Steel / Phenolic, RH (used on RH only!)
10-1
60010-68600 114-10-686-00
1
Acme Back-up Screw (if sold separately)
10-2
60011-01900 (if sold separately)
1
Wear Plate – Slide Hold Down
10-3
60010-72400-WK (if sold separately)
1
Wiper Kit for Slide (Wipers, Spacers, & Screws)
11
60010-80501 114-10-805-01
1
Clamp Bar – Left Side
12
60010-80502 114-10-805-02
1
Clamp Bar – Right Side
13
60010-80701 114-10-807-01
2
Wear Strip, Long – Slide
14
60010-80702 114-10-807-02
2
Wear Strip, Short – Slide
15
60010-80705 114-10-807-05
2
Wear Strip – Clamp Bar, Phenolic
16
60020-62500 114-20-625-00
1
Keeper Plate – Pin
17
60009-68705 114-09-687-05
1
Threaded Rod Adjuster
18
60009-82700 114-09-827-00
1
Holder – Threaded Rod Adjuster
19
60011-01311 114-11-013-11
1
Slide Hold Down Block – Swing Arm
20
60011-01500 114-11-015-00
1
Slide Hold Down Riser – Swing Arm
21
60009-41700 114-09-417-00
1
Key – Bend Die
22
60009-47500 114-09-475-00
1
Nut – Bend Die Stud
23
60009-81600 114-09-816-00
1
Stud – Bend Die (No Overhead Tie Option)
24
60020-23600 114-20-236-00
1
Upper Bearing Cover – Swing Arm
25
60020-42300 114-20-423-00
1
Key – Front Drive Sprocket
26
60020-64000 114-20-640-00
1
Locating Ring – Bend Die
27
60020-73504 114-20-735-04
1
Spacer – Lower Bearing
28
60020-76500 114-20-765-00
1
Drive Sprocket – Front (Tapered Bore Style)
29 (LH)
60020-83100 114-20-831-00
1
Lower Arm Support Bracket – LH (used on LH)
29 (RH)
60025-83100 114-25-831-00
1
Lower Arm Support Bracket – RH (used on RH)
30
60020-15511 114-20-155-11
2
Adjustment Block Kit – Lower Support (Welds)
31
60020-94100 114-20-941-00
1
Spacer – Upper Bearing
32
60040-07501 114-40-075-01
1
Overtravel Switch Trip Plate
33
60040-07502 114-40-075-02
1
Spacer – Overtravel Plate
34
60068-54401 114-68-544-00
1
Safety Plate (Not for all models, call for info)
35
60052-15500 114-52-155-00
1
Slide Back-up Block – 1” (Not Shown)
36
60052-15501 114-52-155-01
1
Slide Back-up Block – 2” (Not Shown)
37
60052-15502 114-52-155-02
1
Slide Back-up Block – 3” (Not Shown)
38
60052-15503 114-52-155-03
1
Slide Back-up Block – 4” (Not Shown)
39
60052-15504 114-52-155-04
1
Slide Back-up Block – 5” (Not Shown)
40
60052-15505 114-52-155-05
1
Slide Back-up Block – 6” (Not Shown)
41
60052-15506 114-52-155-06
1
Slide Back-up Block – 7” (Not Shown)
$1
60024-24200 114-24-242-00
1
Hydraulic Cylinder (Less fittings)
$2
82587 / 82950 (Std. Purchase)
1
Set Upper Spindle Cone / Cup Bearing Set
$3
795 / 792 (Std. Purchase)
1
Set Lower Spindle Cone / Cup Bearing Set
$4
AN-26 (Std. Purchase)
2
Bearing Locknut (for Tapered Drive Sprocket)
$5
AN-24 (Std. Purchase)
1
Bearing Locknut (for Lower Spindle Bearing)
$6
W-24 (Std. Purchase)
1
Locknut Washer (for Lower Spindle Bearing)
$7
LC-150P-18 (Not Pines Std.)
4
Plateform Mount (Not used on all designs)
$8- $41
(Call for info)  
N/A
Standard Purchase Components & Fasteners




Web Site: www.bendersupply.com
© 2008 Haller International Technologies, Inc.


Haller International Technologies, Inc.

Tel: 313-821-0809
Fax: 313-821-0840
E-mail us: info@bendersupply.com

609 St. Jean
Detroit, MI 48214 USA