Pines #1 1/4 & #2 Tube & Pipe Benders
Swing Arm Assembly


Note: Click on large image when it appears for fully expanded view.

KEY
H.I.T. PART NO.
REPLACES
PART NO.
NO.
REQ'D

DESCRIPTION
1 (LH)
30020-07200 112-20-072-00
1
Swing Arm Weldment – LH (CCW)
1 (RH)
30025-07200 112-25-072-00
1
Swing Arm Weldment – RH (CW)
3
30010-29500 112-10-295-00
1
Gib, Slide
3
30010-43000 112-10-430-00
4
Toggle Link (w/ 2 Bushing 30010-43000-BB)
3-A
30010-43000-BB (if sold separately)
8
Bushing Only, Toggle Link (ID Sizing Req’d)
4
30010-50400 112-10-504-00
1
Pin – Upper Rear (Includes $7 & $8)
5
30010-50401 112-10-504-01
1
Pin – Clevis (Includes $6)
6
30010-50600 112-10-506-00
1
Pin – Rod End (Includes $7 & $8)
7
30010-51000 112-10-510-00
1
Pin – Slide (Includes $7 & $8
8
30010-65200 112-10-652-00
1
Rod End – Clamp Cylinder
9 (LH)
30010-72500 112-10-725-00
1
Slide – Ampco Bronze, LH (used on LH only)
9 (RH)
30025-72500 112-25-725-00
1
Slide – Ampco Bronze, RH (used on RH only)
10
30010-80501 112-10-805-01
1
Clamp Bar – Left Side
11
30010-80502 112-10-805-02
1
Clamp Bar – Right Side
12
30010-80700 112-10-807-00
2
Wear Strip - Slide
13
30010-15500 112-10-155-00
1
Slide Hold Down Block – Swing Arm
14
30010-15501 112-10-155-01
1
Wear Strip – Slide Hold Down
15
30009-41700 112-09-417-00
1
Key – Bend Die
16
30009-81600 112-09-816-00
1
Stud – Bend Die (No Overhead Tie Option)
17
30009-94000 112-09-940-00
1
Thrust Washer – Lower Bearing
18
30009-99000 112-09-990-00
1
Castle Locknut – Spindle Bearing
19
30011-01000 112-11-010-00
1
Safety Plate
20
30020-42300 112-20-423-00
1
Key – Front Drive Sprocket
21
30020-62800 112-20-628-00
1
Bend Die Locating Ring – Outer
22
30020-64000 112-20-640-00
1
Bend Die Locating Ring – Inner
23
30020-76500 112-20-765-00
1
Drive Sprocket – Front (Tapered Bore Style)
24
30020-83100 112-20-831-00
1
Lower Arm Support Bracket
25
30040-07501 112-40-075-01
1
Overtravel Switch Trip Plate
26
30040-07502 112-40-075-02
1
Spacer – Overtravel Plate
27
30052-15500 112-52-155-00
1
Slide Back-up Block – 1” (Not Shown)
28
30052-15501 112-52-155-01
1
Slide Back-up Block – 2” (Not Shown)
29
30052-15502 112-52-155-02
1
Slide Back-up Block – 3” (Not Shown)
30
30052-15503 112-52-155-03
1
Slide Back-up Block – 4” (Not Shown)
31
30052-15504 112-52-155-04
1
Slide Back-up Block – 5” (Not Shown)
$1
30024-24200 112-24-242-00
1
Hydraulic Cylinder (Less fittings)
$2
575 / 572 (Std. Purchase)
1 Set
Upper Spindle Cone / Cup Bearing Set
$3
47890 / 47820 (Std. Purchase)
1 Set
Lower Spindle Cone / Cup Bearing Set
$4
AN-16 (Std. Purchase)
2
Bearing Locknut (for Tapered Drive Sprocket)
$5
LC-150P-18 (Not Pines Std.)
4
Plateform Mount (Not used on all designs)
$6 - $30
(Call for info)  
N/A
Standard Purchase Components & Fasteners


Web Site: www.bendersupply.com
© 2008 Haller International Technologies, Inc.


Haller International Technologies, Inc.

Tel: 313-821-0809
Fax: 313-821-0840
E-mail us: info@bendersupply.com

609 St. Jean
Detroit, MI 48214 USA