Pines #3/4 & #1 Tube & Pipe Benders
Swing Arm Assembly


Note: Click on large image when it appears for fully expanded view.

KEY
H.I.T. PART NO.
REPLACES
PART NO.
NO.
REQ'D

DESCRIPTION
1 (LH)
15020-07200 110-20-072-00
1
Swing Arm Weldment – LH (CCW)
1 (RH)
15025-07200 110-25-072-00
1
Swing Arm Weldment – RH (CW)
2
15010-29500 110-10-295-00
1
Gib, Slide
3
15010-43000 110-10-430-00
4
Toggle Link (w/ 2 Bushing 15010-43000-BB)
3-A
15010-43000-BB (if sold separately)
8
Bushing Only, Toggle Link (ID Sizing Req’d)
4
15010-50400 110-10-504-00
1
Pin – Upper Rear (Includes $7 & $9)
5
15010-50401 110-10-504-01
1
Pin – Clevis (Includes $7 & $9)
6
15010-50600 110-10-506-00
1
Pin – Rod End (Includes $8 & $9)
7
15010-51000 110-10-510-00
1
Pin – Slide (Includes $7 & $9)
8
15010-65200 110-10-652-00
1
Rod End – Clamp Cylinder
9 (LH)
15010-72500 110-10-725-00
1
Slide – Ampco Bronze, LH (used on LH only)
9 (RH)
15025-72500 110-25-725-00
1
Slide – Ampco Bronze, RH (used on RH only)
10
15010-80501 110-10-805-01
1
Clamp Bar – Left Side
11
15010-80502 110-10-805-02
1
Clamp Bar – Right Side
12
15010-80700 110-10-807-00
2
Wear Strip - Slide
13
15010-15501 110-10-155-01
1
Slide Hold Down Block – Swing Arm
14
15010-15502 110-10-155-02
1
Wear Strip – Slide Hold Down
15
15009-41700 110-09-417-00
1
Key – Bend Die
16
15009-47500 110-09-475-00
2
Bearing Locknut (for Tapered Drive Sprocket)
17
15009-81600 110-09-816-00
1
Stud – Bend Die (No Overhead Tie Option)
18
15020-42300 110-20-423-00
1
Key – Front Drive Sprocket
19
15020-64000 110-20-640-00
1
Bend Die Locating Ring – Inner
20
15020-76500 110-20-765-00
1
Drive Sprocket – Front (Tapered Bore Style)
21
15020-80700 110-20-807-00
1
Bend Die Locating Ring – Outer
22 (LH)
15020-83101 110-20-831-01
1
Lower Arm Support Bracket, LH (used on LH)
22 (RH)
15025-83101 110-25-831-01
1
Lower Arm Support Bracket, RH (used on RH)
23
30040-07501 112-40-075-01
1
Overtravel Switch Trip Plate
24
30040-07502 112-40-075-02
1
Spacer – Overtravel Plate
25
15068-54400 110-68-544-00
1
Safety Plate
26
15052-15500 110-52-155-00
1
Slide Back-up Block – 1” (Not Shown)
27
15052-15501 110-52-155-01
1
Slide Back-up Block – 2” (Not Shown)
28
15052-15502 110-52-155-02
1
Slide Back-up Block – 3” (Not Shown)
29
15052-15503 110-52-155-03
1
Slide Back-up Block – 4” (Not Shown)
$1
15024-24200 110-24-242-00
1
Hydraulic Cylinder (Less fittings)
$2
3982 / 3920 (Std. Purchase)
1 Set
Upper Spindle Cone / Cup Bearing Set
$3
3975 / 3920 (Std. Purchase)
1 Set
Lower Spindle Cone / Cup Bearing Set
$4
AN-10 (Std. Purchase)
1
Bearing Locknut (for Lower Spindle Bearing)
$5
W-10 (Std. Purchase)
1
Locknut Washer (for Lower Spindle Bearing)
$6
LC-150P-18 (Not Pines Std.)
4
Plateform Mount (Not used on all designs)
$7 - $29
(Call for info)  
N/A
Standard Purchase Components & Fasteners


Web Site: www.bendersupply.com
© 2008 Haller International Technologies, Inc.


Haller International Technologies, Inc.

Tel: 313-821-0809
Fax: 313-821-0840
E-mail us: info@bendersupply.com

609 St. Jean
Detroit, MI 48214 USA